Bottlehead Forum
Bottlehead Kits => Legacy Kit Products => Crack-a-two-a => Topic started by: Happy Ghost on March 25, 2022, 10:25:37 AM
-
Hello All,
Does anyone have any good capacitor upgrade ideas for the C2A. In one of the threads, someone had spoken approvingly of "Dayton Audio DMPC-100 100uF 250V Polypropylene Capacitor".
Folks who have gone the capacitor upgrade path, can you please share some of your experiences and thoughts. btw I already have the 2Quiet upgrade already installed.
Thanks in advance!
-
Hey Atul, I used these and they are fine.
https://www.mouser.com/ProductDetail/Panasonic/EZP-V60107MTC?qs=OlC7AqGiEDkd9vetrBxybA%3D%3D
-
Hey Atul, I used these and they are fine.
hey Lee.. how're you? been long time.. I like the music recommendations you put out every once in a while :)
https://www.mouser.com/ProductDetail/Panasonic/EZP-V60107MTC?qs=OlC7AqGiEDkd9vetrBxybA%3D%3D
So curious on how did you find the sound after this upgrade? is it incremental change or did it make a bigger impact?
-
It was not a drastic change but after the change the presentation was was a little more fluid to my old worn out ears. I generally do not expound on my thoughts as audio is subjective. The film caps were an improvement over the electrolytics supplied, which were not bad I must say.
I am thankful that you got your dac squared away finally, I feel bad in a way for the recommendation but I do love mine. Having said that I will not fall into his trap again.
Those caps are pretty affordable and I consider them an upgrade.
Happy listening my friend.
Lee
-
I believe I put the Audyns in my C2A and they fit/work nicely.
-
It's been a long time since doing the caps, but my bias wants to believe it is better.
Here is what I have done to my Crack/SB since 2014.
1. Alps pot with PCB ... $15
2. RCA Input wires - shielded piece of good Monster I had laying around, separated grounds ... 0$
3. Neutrik Locking TRS jack ... $10
4. Dayton Output Caps - Turrets ... $80
5. 237 ohm stock speedball resistors -> 470 for E80CC
6. Cree Shotkey Diodes with PCB ... $30
7. Triad Choke grounded to IEC ground - replace 270 ohm T15 > T21 resistor ... $20
8. Opposing diodes on IEC ground - noise reduction ... $10
I am more than pleased with the result, however, I would just get a C2A and leave it stock if I were to do it again. It arrived onto the scene just a hair too late for me. BUT, the journey has been rewarding.
What I am really tempted to do is buy a new stock Crack without SB and leave it that way to see just how affected the upgraded (downgraded :-*) Crack/SB is.
-
I am thankful that you got your dac squared away finally, I feel bad in a way for the recommendation but I do love mine. Having said that I will not fall into his trap again.
;D No honestly, I love the DAC!! it is really something special. your honest opinion really did prep me on the supply chain issues.. But it all worked out well :) I might give
Brian a second chance..he actually threw in some upgrades after a few issues piled up ;D
Happy listening my friend.
to you too! Hope Doc is going to put out more projects for all of us to build in 2022 ;D
-
What I am really tempted to do is buy a new stock Crack without SB and leave it that way to see just how affected the upgraded (downgraded :-*) Crack/SB is.
Actually this is my plan too :) Was planning to use something like that just for vinyl listening..
-
Whatever you add, remember to bypass the cap with some Soviet PIO K40/42/MBM/whatever. Trust me comrade, you will be surprised how much tonal difference it can yield. Gotta run as I hear the Capacitor Police rushing in! :) :)