Capacitor "divot"

azrockitman · 1906

0 Members and 1 Guest are viewing this topic.

Offline azrockitman

  • Full Member
  • ***
    • Posts: 222
on: June 27, 2013, 07:00:21 AM
I brushed against one of the large black capacitors on my stereomour kit with my soldering iron shaft. Needless to say, I left a nice little divot on the capacitor housing.  Should I replace it now? Or is it likely fine/unharmed?  No guts or blood appears to be oozing out.  But if I likely did real harm,I'd rather cut my losses now rather than have to pull it out when I'm 100% done.   Any suggestions would be appreciated.   Thanks. 

Esoteric DV-50, Technics SL1200-M3D, B&K Phono 10 Preamp, Sumiko Blue Point Special Evo III, Bottlehead Stereomour, Orca's


Offline HF9

  • Sr. Member
  • ****
    • Posts: 346
  • Zynsonix.com
    • Zynsonix.com
Reply #1 on: June 27, 2013, 07:08:03 AM
Was it a film cap or electrolytic? You may want to post a picture. Seeing the "divot" should allow us to ascertain if it's still usable. Even if you did knick it good, the cost to replace is only a few $$.
« Last Edit: June 27, 2013, 07:09:34 AM by HF9 »

My DIY Audio Electronics Blog: DIYAudioBlog.com


Offline azrockitman

  • Full Member
  • ***
    • Posts: 222
Reply #2 on: June 27, 2013, 07:30:32 AM
It's one of the 220uF 250V electrolytic capacitors

I'll try to post a pic shortly. 

Esoteric DV-50, Technics SL1200-M3D, B&K Phono 10 Preamp, Sumiko Blue Point Special Evo III, Bottlehead Stereomour, Orca's


Offline Doc B.

  • Administrator
  • Hero Member
  • *****
    • Posts: 9643
    • Bottlehead
Reply #3 on: June 27, 2013, 07:43:57 AM
If you just melted the plastic cover with a hot iron there is no problem. If you dented the metal can underneath it should be replaced.

Dan "Doc B." Schmalle
President For Life
Bottlehead Corp.


Offline azrockitman

  • Full Member
  • ***
    • Posts: 222
Reply #4 on: June 27, 2013, 08:31:43 AM
the metal is exposed, but not sure if it's damaged or not

Esoteric DV-50, Technics SL1200-M3D, B&K Phono 10 Preamp, Sumiko Blue Point Special Evo III, Bottlehead Stereomour, Orca's


4krow

  • Guest
Reply #5 on: June 27, 2013, 10:43:54 AM
Yah, at 52kb it's pretty hard to tell  maybe at 200-300kb it would show up.



Offline azrockitman

  • Full Member
  • ***
    • Posts: 222
Reply #6 on: June 27, 2013, 01:19:01 PM
I had to keep reducing the size of the photo to get it to send.  But Doc took a look at it and thought it looked ok so I'm moving forward with fingers crossed.  Thanks.   

Esoteric DV-50, Technics SL1200-M3D, B&K Phono 10 Preamp, Sumiko Blue Point Special Evo III, Bottlehead Stereomour, Orca's


Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19702
Reply #7 on: June 27, 2013, 01:43:25 PM
Those electrolytics are tough, I wouldn't worry too much about it.

(Sorry I didn't see your e-mail until now)

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man