Is this mod recommended?

glynnw · 3631

« previous next »
Pages: 1   Go Down

0 Members and 1 Guest are viewing this topic.

Offline glynnw

  • Full Member
  • ***
    • Posts: 162
on: November 18, 2010, 02:24:54 PM
There is a pair of Paramounts on Audiogon which have had the electrolytic power supply caps replaced with large oil caps by means of an umbilical.  While ungainly, this seems easily doable.  Does anyone have any comments on whether something this drastic would be worthwhile?

Here's a link to them - http://www.audiogon.com/cgi-bin/cls.pl?ampstube&1294029497&/Bottlehead-Paramount-2A3-modif

I have nothing to do with selling these - just looking for ways to improve my Paramounts.

PC, J River software, opticaRendu, Schitt Ygg DAC,Tortuga Pre, Torta Radu tube buffer, Linear Tube Audio ZOTL10, Spatial Audio X5w/pair of GR Research dual 12" open baffle servo subwoofers tamed by DSpeaker Dual-Core DSP , Audience AU24 SE  spkr cable, handmade silver interconnects,

Offline Grainger49

  • Hero Member
  • *****
    • Posts: 7175
Reply #1 on: November 18, 2010, 02:58:39 PM
Glynn,

I like oilers in the power supply.  But I have no experience with them in Paramounts.


Offline ssssly

  • Sr. Member
  • ****
    • Posts: 386
Reply #2 on: November 19, 2010, 03:46:15 AM
Having done something similar I would modify a few things that he did. The last cap in the power supply should be kept in the original case. The benefits you get from upgrading to the oiler and the negative side effect of extending the pathway of that capacitor pretty much cancel each other out. Same for the choke.

I have a FPII clone that I built with an outboard power supply connected via an umbilical. I used double female ended IEC power cables to do it which worked out great (and looked much neater). Tried it much the way this one is at first and didn't hear much of an improvement. But on the advice of a forum member (prob Voltsecond or Grainger) I moved the final PS caps back into the original circuit position and it was a huge improvement. Night and day. I also built a completely separate chassis which the power tranny was attached to. Seems kind of odd to have the power tranny on the original chassis and then run wires out to the PS caps and then run power back in to the chassis.




Offline John Roman

  • Sr. Member
  • ****
    • Posts: 392
Reply #3 on: January 07, 2011, 09:04:35 AM
Hey Glynn,
Just wondering if you figured anything out about this "potential" upgrade. The seller does make it seem interesting though.
John

Regards,
John
Extended Foreplay 3 / 300B Paramount's / BassZilla open baffle/ Music Streamer 2 / Lenovo Y560-Win7-JRMC & JPlay

Offline glynnw

  • Full Member
  • ***
    • Posts: 162
Reply #4 on: January 08, 2011, 05:43:40 AM
Nope - just looked too ungainly.  Concentrating on upgrading crossover to Basszilla at this point.  Just ordered 2 uF OIMP V-Caps to go with the 2 new 50 uF Auricaps I have breaking in.  I sure spend a lot of time and money on these things.

PC, J River software, opticaRendu, Schitt Ygg DAC,Tortuga Pre, Torta Radu tube buffer, Linear Tube Audio ZOTL10, Spatial Audio X5w/pair of GR Research dual 12" open baffle servo subwoofers tamed by DSpeaker Dual-Core DSP , Audience AU24 SE  spkr cable, handmade silver interconnects,

Pages: 1   Go Up
« previous next »