poly tips

aragorn723 · 1937

0 Members and 1 Guest are viewing this topic.

Offline aragorn723

  • Hero Member
  • *****
    • Posts: 1024
on: December 29, 2013, 08:15:57 AM
Can someone give me some tips on making a nice polyurethane finish?  I did 3 coats on my Quickie with some paper towel so far and it isn't quite as smooth as I would like.  (and sanded with 220 grit sandpaper between coats).  Also, how many coats should I do?  Got lots of time this week!!  Thanks.



Offline JamieMcC

  • Hero Member
  • *****
    • Posts: 1167
Reply #1 on: December 29, 2013, 09:42:57 AM
Ditch the paper towel. See if you can find some cheap foam brushes you might be surprised at how nice a finish you can get with them. You will need to put enough on so it flows out as you brush but not so much so it sags or runs when you leave it to stand. If it drags and you have dull and shiny streaks left behind your brush as you brush then your not putting enough on.  The more coats the better imo

(https://forum.bottlehead.com/proxy.php?request=http%3A%2F%2Fwww.artifolk.co.uk%2Fimages%2Fproducts%2F8099x300.jpg&hash=5f4025920a0708d9570e8fe0ce92afc402185d69)

« Last Edit: December 29, 2013, 09:50:03 AM by JamieMcC »

Shoot for the moon if you miss you will still be amongst the stars!


Offline Pfenning

  • Full Member
  • ***
    • Posts: 138
  • My knockoffs
    • This is the place
Reply #2 on: December 29, 2013, 10:56:43 AM
It depends on the type of finish you are wanting. I like wipe on poly because it goes on thin, and feels good to me once it's cured. Sanding in-between coats will improve the finish. If you are looking for a glass smooth finish, it will take quite a few coats, and the bushes recommended here already. I'm not a finish guru, I just like the results I have gotten with wipe on products lately. Good luck.

Pfenning

Pfenning

Paramour 1's with c4s and iron upgrade, Foreplay II, Seduction with c4s, Crack (stock) and Foreplay III (waiting to be built), DIY turntable with Rega RB250 arm with Incognito wiring, Oppo DVD, Pi Stage 4's and DIY subs


Offline Mike B

  • Full Member
  • ***
    • Posts: 248
Reply #3 on: December 29, 2013, 01:37:52 PM
I put mine on with a rag too.  But not a paper towel.

You can get a "pound" of cotton rags inna bag at the hardware if you don't have any old "holey" t-shirts around.

Far away from the bleeding edge


Offline aragorn723

  • Hero Member
  • *****
    • Posts: 1024
Reply #4 on: December 29, 2013, 02:17:15 PM
rags seem to work pretty good, I got a layer on with that, but it is super thin, guess I need a bunch more?



Offline galyons

  • Sr. Member
  • ****
    • Posts: 626
  • Geary Lyons
Reply #5 on: December 29, 2013, 02:22:42 PM
You want thin!  Thin and multiple layers will give the nicest finish.

Cheers,
Geary

VPI TNT IV/JMW 3D 12+Benz LP-S>  Eros + Auralic Aries + ANK Dac 4.1 >Eros TH+ Otari MX5050 IIIB2 > BeePre >Paramount 300B 7N7 > EV Sentry IV-A

Thorens TD124/Ortofon RMG-212/SPU >Seduction > Smash^Up> Paramour 45 MQ >K12's


Offline Mike B

  • Full Member
  • ***
    • Posts: 248
Reply #6 on: December 29, 2013, 04:07:14 PM
Yup, that's the secret, multiple thin coats.

The first coat I use a cheap disposable brush.  I put it on heavy 'cause I know it's gonna soak in.  But not gloppy heavy, I brush it out even.

All the rest I rub.

Far away from the bleeding edge


Offline Deluk

  • Sr. Member
  • ****
    • Posts: 440
Reply #7 on: December 30, 2013, 10:51:25 AM
220 grit is VERY rough. OK for initial wood finishing. Getting the wood as smooth as possible first is always needed. First coats of finish will tend to lift the grain a bit and this has to be smoothed back before you can start to get it smooth to the touch. No dust! Wipe off with a tack rag after sanding. If your coats are very thin 800 grit will be fine enough.



Offline JamieMcC

  • Hero Member
  • *****
    • Posts: 1167
Reply #8 on: December 30, 2013, 12:52:27 PM
For pointers there are plenty of videos on applying poly on youtube.

Shoot for the moon if you miss you will still be amongst the stars!