Terminal 1 measures high in voltage test [resolved]

Universe Man · 1575

0 Members and 1 Guest are viewing this topic.

Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
on: August 14, 2021, 06:01:29 PM
I measured terminal 1 as instructed and got a value of ~125v. Any suggestions? Passes resistance test and both LEDs and tubes turn on.

I’ll add that terminal 2 measures in the acceptable range.
« Last Edit: August 17, 2021, 03:01:43 AM by Universe Man »



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19316
Reply #1 on: August 15, 2021, 05:37:31 AM
Can you post some build photos?  What are the voltages on terminals 1-10?  You can't have both terminal 7 and 9 have acceptable voltages with 125V on terminal 1.

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man


Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #2 on: August 15, 2021, 06:50:23 AM
1 120
2 160
3 0
4 161
5 118
6 0
7 128
8 0
9 126
10 0



Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #3 on: August 15, 2021, 09:12:04 AM
Can you post some build photos?  What are the voltages on terminals 1-10?  You can't have both terminal 7 and 9 have acceptable voltages with 125V on terminal 1.
I checked over all the joints a couple times and they all seemed okay. Unless there is something I’m just missing repeatedly, which there might likely be, I’m not sure what could be wrong.



Offline Doc B.

  • Administrator
  • Hero Member
  • *****
    • Posts: 9538
    • Bottlehead
Reply #4 on: August 15, 2021, 09:41:24 AM
Posting photos may help.

Dan "Doc B." Schmalle
President For Life
Bottlehead Corp.


Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #5 on: August 15, 2021, 09:43:24 AM
Posting photos may help.
I put a couple in a reply above



Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #6 on: August 15, 2021, 10:24:39 AM
Posting photos may help.
Do you think more angles are needed?



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19316
Reply #7 on: August 15, 2021, 12:46:04 PM
If you pull the 6080 and run the amp with just the 12AU7, what voltage do you get at terminal 1?

Also, can you carefully measure the DC voltage at A3?

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man


Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #8 on: August 15, 2021, 02:56:04 PM
If you pull the 6080 and run the amp with just the 12AU7, what voltage do you get at terminal 1?

Also, can you carefully measure the DC voltage at A3?
1 is 152 without the tube

A3 is 2v



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19316
Reply #9 on: August 16, 2021, 07:11:10 AM
Looking back over this with fresh eyes, your voltages on 1 and 5 are too high.  This would have me more suspicious that you have a bad solder joint on the green twisted pair of wires running between the octal socket and the 9 pin socket, and you aren't getting the 12AU7 all the way hot because of that. 


Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man


Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #10 on: August 16, 2021, 12:44:01 PM
Looking back over this with fresh eyes, your voltages on 1 and 5 are too high.  This would have me more suspicious that you have a bad solder joint on the green twisted pair of wires running between the octal socket and the 9 pin socket, and you aren't getting the 12AU7 all the way hot because of that.
I touched up those joints but t1 still goes up then settles around 122
« Last Edit: August 16, 2021, 12:51:22 PM by Universe Man »



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19316
Reply #11 on: August 16, 2021, 01:04:06 PM
Is the 12AU7 glowing up top?

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man


Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #12 on: August 16, 2021, 01:06:04 PM



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19316
Reply #13 on: August 16, 2021, 01:11:28 PM
Can you double check that you didn't get a 12AT7 by mistake?

Something just isn't adding up here...

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man


Offline Universe Man

  • Jr. Member
  • **
    • Posts: 21
Reply #14 on: August 16, 2021, 01:16:46 PM
Can you double check that you didn't get a 12AT7 by mistake?

Something just isn't adding up here...
Box says 12au7, tube text is worn down a bit and harder to interpret. Might look like it says At or something? What do you think?