News:
October 24, 2021, 02:36:30 AM

Author Topic: Revisiting the question of how to wire the head(s)  (Read 557 times)

0 Members and 1 Guest are viewing this topic.

Offline PS2500

  • Full Member
  • ***
  • Posts: 67
Revisiting the question of how to wire the head(s)
« on: August 08, 2021, 10:13:02 PM »
In this subforum, Doc B answered a question of mine about keeping the internal preamp of a tape deck available by suggesting cutting the wires between the head and the preamp. Reading it over, I thought I got it, but actually no.

Instead of a switch you could cut the internal cables. Run the part of the cables left connected to the internal preamp to a second pair of RCA jacks, as well as running the end left connected to the playback head to a pair of RCA jacks. Then you can use an interconnect to connect the head either to an outboard playback preamp or loop it back into the internal preamp. That's basically how I use my Nagra T, with different connectors.

I've been thinking about how this would work in a Technics RS1500. There are two line outs available on the back of the deck, as well as a line in and a "through out". I assume the through out is for directly outputting a source that you might be recording from to an amplifier. If so, I don't really need it and could repurpose that connector.

So while I'm still not totally clear about Doc B's suggestion, I think a Technics deck could have 3 RCA connections on the back that can be rewired (keeping the 4th, the line in, for recording, of course). One for direct connection from the playback head, and from there over interconnect to an Eros amp. One for direct connection to the OUT side of the internal preamp board. And then one to the IN side of the internal preamp board?

Do I have that right? If so, then the back of the deck could have a "playback head out", an "internal preamp head out" and an "internal preamp in" connector? And then to use the internal amp, just use an interconnect to bridge playback head out and internal preamp in?

Finally, is it possible to have both the 4 tr head and the 2 tr head wired directly to the output at the back of the deck?
« Last Edit: August 08, 2021, 10:47:50 PM by PS2500 »

Offline Doc B.

  • Administrator
  • Hero Member
  • *****
  • Posts: 8733
    • Bottlehead
Re: Revisiting the question of how to wire the head(s)
« Reply #1 on: August 09, 2021, 06:57:00 AM »
What is an internal preamp head out?

Leave the line input jack alone. Leave the line output 1 jack alone. Cut the wires to the line output 2 jack and connect the internal play head cables coming from the head to those jacks instead of the internal preamp. Cut the wires to the throughout jacks and connect those jacks to the input of the internal playback preamp. Then you can run interconnects from the head out jacks (labeled line output 2) to either an Eros or to the internal playback preamp jacks (labeled throughout).

Both play heads play thru the same internal head cables going to the preamp. They meet at the switch in the head block, before those cables.

I will suggest getting an RS1500 service manual and studying the schematics.
Dan "Doc B." Schmalle
President For Life
Bottlehead Corp.

Offline PS2500

  • Full Member
  • ***
  • Posts: 67
Re: Revisiting the question of how to wire the head(s)
« Reply #2 on: August 10, 2021, 02:18:35 AM »
Quote
What is an internal preamp head out?

Yes, sorry, I meant to say internal preamp out. Thanks for the explanation, I've got it now. Will definitely be looking at the schematic of course, before I do anything with the wires. I originally had this project in mind for a different machine but now have a Technics RS1500 that I would prefer to use instead. I suspended the build itself several times while I had other projects on the go, so it's been glacially slow, but I restarted recently and want to carry through to the end in the near future.