PAS-2 Preamp inputs

Rowbo1 · 2758

« previous next »
Pages: 1   Go Down

0 Members and 1 Guest are viewing this topic.

Offline Rowbo1

  • Newbie
  • *
    • Posts: 4
on: January 26, 2011, 10:59:55 AM
Hello, I am new to the forum and look forward to learning all I can from all the  members here. I have a PAS-2 preamp that only seems to like inputs such as turntable and RR at the "Tape" input,  All other are very low and distorted. Is the unit prone to this with age. and when working properly is there a prefered input to use. I have a ST-70 on one end and have had the best fidelity so far with a TEAC 32. Turntable also works fine with a NAD preamp but again they have to be going into "Tape" Input. I am a Electronic tech and will be rebuiling both dynacos in the future for both looks and upgrades.
Thanks Dave

Dave Rowbotham
ST70 PAS2 TEAC 32 TT in work

Offline Doc B.

  • Administrator
  • Hero Member
  • *****
    • Posts: 9657
    • Bottlehead
Reply #1 on: January 26, 2011, 11:10:52 AM
Hi Dave,

This forum is really intended for discussion of Bottlehead products. You would probably find a wealth of info about your PAS-2 at this forum:

http://www.audioasylum.com/cgi/tv.mpl?s=1&v=e&forum=dynaco

Dan "Doc B." Schmalle
President For Life
Bottlehead Corp.

Offline Rowbo1

  • Newbie
  • *
    • Posts: 4
Reply #2 on: January 26, 2011, 11:27:56 AM
Quote from: Doc B. on January 26, 2011, 11:10:52 AM
Hi Dave,

This forum is really intended for discussion of Bottlehead products. You would probably find a wealth of info about your PAS-2 at this forum:

http://www.audioasylum.com/cgi/tv.mpl?s=1&v=e&forum=dynaco [nofollow]
My bad, I assumed with the 50 sum responses to the Dynaco ST70 thread below I would find some help.
Regards Dave

Dave Rowbotham
ST70 PAS2 TEAC 32 TT in work

Offline Doc B.

  • Administrator
  • Hero Member
  • *****
    • Posts: 9657
    • Bottlehead
Reply #3 on: January 26, 2011, 11:46:09 AM
I didn't say that no one would help. I was trying to suggest a place that specifically deals with your preamp and that probably has more info about repairing it. I'm sure there are guys here who have had a PAS. I've had a few myself. I don't recall having the problem you are experiencing, but if your highest gain inputs work OK and the lower gain ones don't it could just be a bad selector switch.

Dan "Doc B." Schmalle
President For Life
Bottlehead Corp.

Offline Rowbo1

  • Newbie
  • *
    • Posts: 4
Reply #4 on: January 26, 2011, 11:56:41 AM
Quote from: Doc B. on January 26, 2011, 11:46:09 AM
I didn't say that no one would help. I was trying to suggest a place that specifically deals with your preamp and that probably has more info about repairing it. I'm sure there are guys here who have had a PAS. I've had a few myself. I don't recall having the problem you are experiencing, but if your highest gain inputs work OK and the lower gain ones don't it could just be a bad selector switch.
Thank You, that is great advice on the levels. The Audoasylum forum looks like a huge dynaco resource. I will be looking at you tape preamp once I get my front end up to snuff

Dave

Dave Rowbotham
ST70 PAS2 TEAC 32 TT in work

Offline Grainger49

  • Hero Member
  • *****
    • Posts: 7175
Reply #5 on: January 26, 2011, 12:43:27 PM
Dave,

You have a lengthy PM.
« Last Edit: January 27, 2011, 11:45:35 AM by Grainger49 »


Offline Rowbo1

  • Newbie
  • *
    • Posts: 4
Reply #6 on: January 26, 2011, 01:31:16 PM
Shure Email [email protected]
Dave

Dave Rowbotham
ST70 PAS2 TEAC 32 TT in work

Pages: 1   Go Up
« previous next »