Waiting for the price of that pricey cap/wire/whatever to come down?

Downhome Upstate · 13041

0 Members and 1 Guest are viewing this topic.

Offline earwaxxer

  • Hero Member
  • *****
    • Posts: 1336
Thanks for the info Cliff - I'll have to put that mod on my short list!

Eric
Emotiva XPA-2, Magnepan MMG (mod), Quickie (mod), JRiver, Wyrd4sound uLink, Schiit Gungnir, JPS Digital power cord, MIT power cord, JPS Labs ultraconductor wire throughout, HSU sub. powered by Crown.


4krow

  • Guest
  Cliff,   The idea of using Elna is solid. If one would only fit into my integrated. I think that I might be doing some measuring before the nights over. The Elna single deck might just work.



Offline chard

  • Full Member
  • ***
    • Posts: 75
Eric and Greg, One thing I did was take a 1" x 1" 1/2 board and made a six eyelet board. I took apart a terminal strip removing all metal parts except the foot that bolts to the chassis and enough board to glue to the eyelet board. This gave me have an upright eyelet board with eyelets in about the same position as the pot eyelets. This allowed me to disconnect the selector switch shielded cables and input shielded cables from the pot and solder them to the eyelet board instead. By doing this I didn't have to redo any of the shielded cable other then disconnecting it from the pot and soldering it to the eyelet board instead.   
  I used two 4 terminal, terminal strips positioned on either side of the switch about 1 inch from the switch to connect the shunt resisters to ground. 

Clifford Hard


Offline Grainger49

  • Hero Member
  • *****
    • Posts: 7175
The job is coming to an end.  I have to make a decision.  Where do I want to put some high $ caps?  The Eros has 0.47uF Mundorf Silver/Gold/Oil, the FP 2 has 0.47uF Mundorf Silver/Oil, the Paramours have four caps waiting to be installed (Mundorf Silver/Oil and Clarity caps). 

So where do I want to change it up?  I seem to have too small a cap in the FP 2.  It should be 2uF or larger, I could have been under the influence for that order.

Any suggestions?  The cash is going to run out in 5 weeks!



Offline corndog71

  • Sr. Member
  • ****
    • Posts: 593
Try a pair of Sonicap Gen 1.  You can get a matched pair from Sonicraft.com

The world was made for those not cursed with self-awareness.

Rob


Offline Grainger49

  • Hero Member
  • *****
    • Posts: 7175
For what piece? 



Offline corndog71

  • Sr. Member
  • ****
    • Posts: 593
For what piece? 

For the FP 2.  Not too spendy either.

The world was made for those not cursed with self-awareness.

Rob


Offline earwaxxer

  • Hero Member
  • *****
    • Posts: 1336
2uF or higher.... I assume you need two, that could get pricey, but a good size to have on hand. I honestly recommend the Mundorf silver/oil in that size. I have four of those in the 2.2uF. They come in handy. I think the Mundorf silver/oil is a better value over the silver/gold/oil. I think it's the smart choice in lew of a Duelund or V-cap... I know, you're prob looking for some sexy new bitch. Sometimes it's good to stay with what you know!

Eric
Emotiva XPA-2, Magnepan MMG (mod), Quickie (mod), JRiver, Wyrd4sound uLink, Schiit Gungnir, JPS Digital power cord, MIT power cord, JPS Labs ultraconductor wire throughout, HSU sub. powered by Crown.


Offline johnsonad

  • Hero Member
  • *****
    • Posts: 1670
Eric has got a good point, stick with what you know and like.  I'm going out on a limb with the Jupiters but every once in a while you need to do that, right?

Aaron Johnson


Offline earwaxxer

  • Hero Member
  • *****
    • Posts: 1336
Cool! Can't wait to hear what you think

Eric
Emotiva XPA-2, Magnepan MMG (mod), Quickie (mod), JRiver, Wyrd4sound uLink, Schiit Gungnir, JPS Digital power cord, MIT power cord, JPS Labs ultraconductor wire throughout, HSU sub. powered by Crown.


Offline Grainger49

  • Hero Member
  • *****
    • Posts: 7175
Rob,

Got you now.  The Sonicaps are downright cheap.  I have had them bookmarked for ages and never done anything with it. 

I can buy those and a pair of Mundorfs.  I'll do that.



Offline earwaxxer

  • Hero Member
  • *****
    • Posts: 1336
Granger - you will have to let us know about the Sonicaps - they get very little press, they could be a sleeper value

Eric
Emotiva XPA-2, Magnepan MMG (mod), Quickie (mod), JRiver, Wyrd4sound uLink, Schiit Gungnir, JPS Digital power cord, MIT power cord, JPS Labs ultraconductor wire throughout, HSU sub. powered by Crown.


Offline Grainger49

  • Hero Member
  • *****
    • Posts: 7175
Yup, I'll send myself a link at work to order tomorrow.



Offline tsingle999

  • Sr. Member
  • ****
    • Posts: 275
  • We are all here because we are not all there.
Well i definitely like the clarity cap mr as a parafeed cap over the mundorf supreme or auricap. Very detailed and spacious bringing a little more life too. Thanks to Deb for the initial recommendation. Thanks to parts express to be out of stock when i ordered and then madisound for having them half price a short time later!

SGS iTransporter with Qobuz & Roon to Optical Rendu to BH DAC (Battery) / Wavelegth Cosecant to BeePre to 300b(ehemoths) to Jagers.
Bottlehead Stat headphone amp with Wavelength Brick DAC


Offline earwaxxer

  • Hero Member
  • *****
    • Posts: 1336
 Very curious about the MR!

Eric
Emotiva XPA-2, Magnepan MMG (mod), Quickie (mod), JRiver, Wyrd4sound uLink, Schiit Gungnir, JPS Digital power cord, MIT power cord, JPS Labs ultraconductor wire throughout, HSU sub. powered by Crown.