Mains hum+ FFT graph included

Shamsyrup · 1239

0 Members and 1 Guest are viewing this topic.

Offline Shamsyrup

  • Jr. Member
  • **
    • Posts: 14
on: June 23, 2021, 09:57:53 AM
Hi, previously my stock crack had a slight audible hum. I tried resoldering every joint with new solder and cleaned all the pins. Used bigger caps but the issues remained. Surprisingly when I changed the power supply diodes to a single package vishay bridge rectifier the audible hum was gone, well at least with hd600s. But when I use the 600ohm beyerdynamic dt990 I can again hear the slight hum although not as noticeable as before. Same with high impedance iems. The hum does not change with the volume knob.  The magnitude remains same no matter how much I turn the volume knob or change the dac volume. My mains frequency is 50hz.

Is there any solution ? Or this is just normal for crack ? Any suggestions are highly appreciated.

Thank you.



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19694
Reply #1 on: June 23, 2021, 04:08:09 PM
Can you post some build photos?  Are the mains power outlets where you are earthed?

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man


Offline diynewbie

  • Full Member
  • ***
    • Posts: 68
Reply #2 on: June 24, 2021, 01:17:18 AM
I would have thought that a 1 khz hum would have been coming from outside of the crack - either something on mains, in the source chain or through the air.  Is it common for circuitry like the Crack to generate such frequencies?



Offline Shamsyrup

  • Jr. Member
  • **
    • Posts: 14
Reply #3 on: June 24, 2021, 01:30:40 AM
Can you post some build photos?  Are the mains power outlets where you are earthed?

Yes I will post pictures as soon a reach home.



Offline Shamsyrup

  • Jr. Member
  • **
    • Posts: 14
Reply #4 on: June 24, 2021, 01:32:04 AM
I would have thought that a 1 khz hum would have been coming from outside of the crack - either something on mains, in the source chain or through the air.  Is it common for circuitry like the Crack to generate such frequencies?

1khz is the signal I am injecting. Actual hum is 50hz and it's 2nd order harmonic of 100hz.



Offline Paul Joppa

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 5822
Reply #5 on: June 24, 2021, 04:54:16 AM
1khz is the signal I am injecting. Actual hum is 50hz and it's 2nd order harmonic of 100hz.
What is the voltage of that 1kHz input? Is the gain setting at maximum?
« Last Edit: June 24, 2021, 04:56:00 AM by Paul Joppa »

Paul Joppa


Offline Shamsyrup

  • Jr. Member
  • **
    • Posts: 14
Reply #6 on: June 24, 2021, 08:14:22 AM
What is the voltage of that 1kHz input? Is the gain setting at maximum?
Line voltage is about 1.8volt p2p. Which gain ? The gain of crack or the interface ?

Can you post some build photos?  Are the mains power outlets where you are earthed?

I have added the pictures of mains connection and grounding. Also attached some more measurements and pictures.



Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19694
Reply #7 on: June 24, 2021, 05:24:31 PM
Can you post a picture of the solder and a picture of any flux that you used?

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man