News:
September 27, 2021, 07:05:12 AM

Author Topic: Mono wiring questions  (Read 305 times)

0 Members and 1 Guest are viewing this topic.

Offline Karl5150

  • Sr. Member
  • ****
  • Posts: 509
Mono wiring questions
« on: August 26, 2021, 04:39:46 AM »
Looking at the instructions for wiring the output for mono on page 38 (with an eye towards reverting back to stereo if the mood strikes in the future) would running a wire directly from the ground tab to the black post of the right output work equally well? My thinking is that the wire running from the ground tab to the red post of the left output could simply be clipped, stripped and attached to the black post of the left output for stereo operation.
Also, is my single speaker wiring correct in the photo?
Thanks as always,
Karl   
Karl
Downstairs: Planar3>Eros>Stereomour II>diy OB Betsy+
Upstairs: DIY RP1>Reduction / CD5004>Seductor/SEX 3.1.1>FH3/DT770 pro/HE-4xx
Office: Schiit Modi Uber 2 / Sirius Tuner>SEX 2.1.1>µFonken FF85WK with diy subs
Garage: CA x12 streamer>Quicksand>Minimus 77

Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 15596
Re: Mono wiring questions
« Reply #1 on: August 26, 2021, 05:33:22 AM »
That shouldn't be a problem if you do it that way.  Do you have two Seductors?
Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man

Offline Karl5150

  • Sr. Member
  • ****
  • Posts: 509
Re: Mono wiring questions
« Reply #2 on: August 26, 2021, 08:09:24 AM »
I'm working on the second one now. I've been running the original for several years into a pair of Alpair 7.3 drivers. They seem to be happy with the higher damping factor of the Seductor but will no doubt be able to use the extra juice offered by a pair.
Thanks as always,
Karl
Karl
Downstairs: Planar3>Eros>Stereomour II>diy OB Betsy+
Upstairs: DIY RP1>Reduction / CD5004>Seductor/SEX 3.1.1>FH3/DT770 pro/HE-4xx
Office: Schiit Modi Uber 2 / Sirius Tuner>SEX 2.1.1>µFonken FF85WK with diy subs
Garage: CA x12 streamer>Quicksand>Minimus 77

Offline Karl5150

  • Sr. Member
  • ****
  • Posts: 509
Re: Mono wiring questions
« Reply #3 on: September 02, 2021, 06:24:07 AM »
Remembering, correctly I hope, a post from Doc that wiring the OTs for 4 Ohm output would give the quietest operation with headphones (I built one of Josh's adapters) and the recent PJ post that it would offer increased damping factor over the 8 Ohm setting, I wired both sets for 4 Ohm mono operation.
What would the expected reduction in power be when connected to a pair of nominal 8 Ohm speakers as opposed to the 8 Ohm output?
Karl 
Karl
Downstairs: Planar3>Eros>Stereomour II>diy OB Betsy+
Upstairs: DIY RP1>Reduction / CD5004>Seductor/SEX 3.1.1>FH3/DT770 pro/HE-4xx
Office: Schiit Modi Uber 2 / Sirius Tuner>SEX 2.1.1>µFonken FF85WK with diy subs
Garage: CA x12 streamer>Quicksand>Minimus 77

Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 15596
Re: Mono wiring questions
« Reply #4 on: September 02, 2021, 06:26:58 AM »
You'll get about half the output power.
Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man

Offline Karl5150

  • Sr. Member
  • ****
  • Posts: 509
Re: Mono wiring questions
« Reply #5 on: September 08, 2021, 02:20:21 AM »
Thanks, I didn't realize it was such a direct correlation, although specs often show a doubling of power when using speakers of half the resistance (I installed lots of trunk subs in the 90s)
I guess I'll just have to try both settings to find the sweet spot.
Karl
Karl
Downstairs: Planar3>Eros>Stereomour II>diy OB Betsy+
Upstairs: DIY RP1>Reduction / CD5004>Seductor/SEX 3.1.1>FH3/DT770 pro/HE-4xx
Office: Schiit Modi Uber 2 / Sirius Tuner>SEX 2.1.1>µFonken FF85WK with diy subs
Garage: CA x12 streamer>Quicksand>Minimus 77