C4S LED and voltage issue

Loquah · 5317

« previous next »
Pages: 1 2 3   Go Down

0 Members and 1 Guest are viewing this topic.

Offline Loquah

  • Sr. Member
  • ****
    • Posts: 507
  • Accidental Tube Addict
    • Passion For Sound
Reply #30 on: May 12, 2020, 09:12:54 PM
Quote from: Paul Birkeland on May 12, 2020, 07:01:53 PM
OK, so the OB voltage that really wanted to spend the rest of its life at 6V has popped back up without the regulator in the way.

I believe your issue will be resolved by replacing the 431 regulator on the offending channel, with the slightest possibility that you'll also need a 12AU7. 

-PB

Thanks Paul - I appreciate your help and patience. I've ordered the required parts and will advise once installed
« Last Edit: May 12, 2020, 11:30:14 PM by Loquah »

Check out my reviews on YouTube - https://youtube.com/c/passionforsound

Offline Loquah

  • Sr. Member
  • ****
    • Posts: 507
  • Accidental Tube Addict
    • Passion For Sound
Reply #31 on: May 14, 2020, 10:23:39 PM
I've replaced the TL431 and swapped in a fresh 12AU7. All voltages are correct EXCEPT Kreg (B side) is still reading only 6V.

All tubes are new compared to when original issue arose.

Check out my reviews on YouTube - https://youtube.com/c/passionforsound

Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19750
Reply #32 on: May 15, 2020, 05:22:27 AM
Are you able to adjust the bias per the instructions in the manual?

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man

Offline Loquah

  • Sr. Member
  • ****
    • Posts: 507
  • Accidental Tube Addict
    • Passion For Sound
Reply #33 on: May 15, 2020, 03:22:41 PM
Yes! I think the A-side trim pot was out of range if there's such a thing. A few extra turns and I'm back in range.

Thanks so much, Paul. Can I ask one more question?

Should I be wary of trying any of the previous tubes back in the amp? If the tubes have failed could they cause problems if I reinsert them?

Check out my reviews on YouTube - https://youtube.com/c/passionforsound

Offline diynewbie

  • Full Member
  • ***
    • Posts: 68
Reply #34 on: May 16, 2020, 01:15:57 AM
Good question, looking forward to Paul's reply.  I would suggest that you download data sheets and use your meter to check for shorts.


Offline Paul Birkeland

  • Global Moderator
  • Hero Member
  • *****
    • Posts: 19750
Reply #35 on: May 16, 2020, 04:43:38 AM
The amp should tolerated shorted 6C45PI tubes pretty well.  Things will heat up if you leave them in there running for a long time though.

Paul "PB" Birkeland

Bottlehead Grunt & The Repro Man

Offline Loquah

  • Sr. Member
  • ****
    • Posts: 507
  • Accidental Tube Addict
    • Passion For Sound
Reply #36 on: May 16, 2020, 03:25:11 PM
Quote from: Paul Birkeland on May 16, 2020, 04:43:38 AM
The amp should tolerated shorted 6C45PI tubes pretty well.  Things will heat up if you leave them in there running for a long time though.

Thanks, Paul. I'll fire it up quickly, check for sound (with sacrificial test headphones) and respond accordingly

Check out my reviews on YouTube - https://youtube.com/c/passionforsound

Pages: 1 2 3   Go Up
« previous next »